SOCIETY NEWS TECH TOPICS Standards for Public Review C7.3M:201X, Process Specification for Electron Beam Welding. $52. 3/23/15. P. Portela, pportela@aws.org, ext. 311. D1.5M/D1.5: 201X, Bridge Welding Code. $176. S. Borrero, sborrero@aws. org, ext. 334. D1.1/D1.1M:201X, Structural Welding Code — Steel. $264. 4/6/15. J. Molin, jmolin@aws.org, ext. 304. AWS was approved as an accredited standards-preparing organization by the American National Standards Institute (ANSI) in 1979. AWS rules, as approved by ANSI, require that all standards be open to public review for comment during the approval process. The above revised standards are submitted for public review. A draft copy may be obtained from the staff member listed. ISO Draft Standards for Public Review ISO/DIS 5182, Resistance welding — Materials for electrodes and ancillary equipment. ISO/DIS 9692.3, Welding and allied processes — Recommendations for joint preparation — Part 3: Metal inert gas Opportunities to Contribute to AWS Technical Committees The following committees welcome new members. Some committees are recruiting members with specific interests in regard to the committee’s scope, as marked below: Producers (P); General Interest (G); Educators (E); Consultants (C); and Users (U). For more information, contact the staff member listed or visit www.aws.org/w/a/technical/comm_stand.html. 86 WELDING JOURNAL / APRIL 2015 welding and tungsten inert gas welding of aluminium and its alloys. ISO/DIS 15011-1, Health and safety in welding and allied processes — Laboratory method for sampling fume and gases — Part 1: Determination of fume emission rate during arc welding and collection of fume for analysis. ISO/DIS 17637, Non-destructive testing of welds — Visual testing of fusion welded joints. ISO/DIS 17662, Welding — Calibration, verification and validation of equipment used for welding, including ancillary activities. Technical Committee Meetings April 7–10. D1 Committee and Subcommittees on Structural Welding. Miami, Fla. J. Molin, jmolin@aws.org, ext. 304. April 22. SH4 Subcommittee on Labeling and Safe Practices. Pittsburgh, Pa. S. Hedrick, steveh@aws.org, ext. 305. April 28. B2E Subcommittee on Soldering Qualification. Colorado Springs, Colo. J. Rosario, jrosario@ aws.org, ext. 308. April 29. B2A Subcommittee on Brazing Qualification, B2B Subcommittee on Welding Qualification, B2D Subcommittee on Standard Welding Procedure Specifications. Colorado Springs, Colo. J. Rosario, jrosario@aws.org, ext. 308. April 29. SH1 Subcommittee on Fumes and Gases. Columbus, Ohio. S. Hedrick, steveh@aws.org, ext. 305. April 30. B2 Committee on Procedure and Performance Qualification. Colorado Springs, Colo. J. Rosario, jrosario@aws.org, ext. 308. May 6, 7. A2 Committee and Subcommittees on Definitions and Symbols. Columbus, Ohio. S. Borrero, sborrero@aws.org, ext. 334. May 11. C1 Committee on Resistance Welding, J1 Committee and Subcommittees on Resistance Welding Equipment. Livonia, Mich. E. Abrams, eabrams@aws.org, ext. 307. May 12. D8 Committee and Subcommittees on Automotive Welding. Livonia, Mich. E. Abrams, eabrams@aws.org, ext. 307. May 18–21. D17 Committee and Subcommittees on Welding in the Aircraft and Aerospace Industries. J. Molin, jmolin@aws.org, ext. 304. E. Abrams, eabrams@aws.org, ext. 307 Methods of weld inspection, B1 Committee (E, U). Automotive, D8 Committee (C, E, G, U). Cranes, presses, and industrial mill rolls, D14E and H Subcommittees (C, E, G, U). Resistance welding, C1 Committee (C, E, G, U). Resistance welding equipment, J1 Committee (E, G, U). A. Naumann, anaumann@aws.org, ext. 313 Oxyfuel gas welding and cutting, C4 Committee (C, E, G, U). Friction welding, C6 Committee. Welding practices and procedures for austenitic steels, D10C Subcommittee. Aluminum piping, D10H Subcommittee. Chromium molybdenum steel piping, D10I Subcommittee. Welding of titanium piping, D10K Subcommittee. Purging and root pass welding, D10S Subcommittee. Lowcarbon steel pipe, D10T Subcommittee. Orbital pipe welding, D10U Subcommittee. Duplex pipe welding, D10Y Subcommittee. Reactive alloys, G2D Subcommittee (G). Titanium and zirconium filler metals, A5K Subcommittee. P. Portela, ext. 311, pportela@aws.org Highenergy beam welding and cutting, C7 Committee. Robotic and automatic welding, D16 Committee (C, E, G). Hybrid welding, C7D Subcommittee (G). J. Rosario, ext. 308, jrosario@aws.org Procedure and performance qualification, B2 Committee (E). Thermal spraying, C2 Committee (C, E, G, U). Welding iron castings, D11 Committee (C, E, G, P, U). Railroad welding, D15 Committee (E, G). J. Molin, ext. 304, jmolin@aws.org Welding sheet metal, D9 Committee (G, P). S. Hedrick, ext. 305, steveh@aws.org Joining of plastics and composites, G1 Committee. Safety and Health Committee (E, U, G, C). Mechanical testing of welds, B4 Committee. R. Gupta, ext. 301, gupta@aws.org Magnesium alloy filler metals, A5L Subcommittee.
Welding Journal | April 2015
To see the actual publication please follow the link above